By Olivier Constance. Car Wiring. Publised at Wednesday, August 09th 2017, 01:55:58 AM. Cut out all the damaged wires with wire cutters. Spread out the cuts across a bundle of several wires: if many joins are opposite each other their bulk may make it difficult to fit the loom into the car. If possible, replace wiring with new wire of the same colour. The new wire must be the right size: there are five sizes, depending on current rating. Repairs in wrapped sections of the loom are the only places where you may join wires by twisting them together and soldering the joint mainly because there may not be room for any other method.
By Mailys Laurent. Electrical Wiring. Published at Thursday, December 28th 2017, 05:20:31 AM. The datasheet states (see image below) that this IC—specifically the CMOSens® technology that it uses—is "designed for mass production." Umm, should not this go without saying? I have seen datasheets state "not recommended for new designs," but I do not ever recall seeing one that specifies that the IC, or its underlying technology, is designed for mass production. This benefit makes me question if Sensirion has other ICs that are in fact not designed for mass production. It is all a bit puzzling. Have you seen other IC datasheets call this out? If so, please let us know.
By Cyrille Lothaire. Electrical Wiring. Published at Thursday, December 28th 2017, 05:00:05 AM. PCBs with SMT on both sides and those with mixed TH and SMTs may start to flex and bow when in the reflow oven or selective soldering machine. For this reason, the maximum size for this type of board is usually smaller than the single-sided. Breaking out the boards manually can stress the board and components near the edges, the solder joints, or leave out rough stubs on the edges
By Adrienne Emmanuel. Car Wiring. Published at Thursday, December 28th 2017, 03:09:28 AM. Ring terminal This alternative to the spadeterminal is used on heavier components. "Scotchlok" connector The "Scotchlok" connector splices two wires together, using asharp metal blade which pierces theinsulation. This is clamped using a pair ofpliers, and covered with a plastic clip.
By Claudine Nicolette. Electrical Wiring. Published at Thursday, December 28th 2017, 00:08:10 AM. As you may have noticed, this is one of those annoying situations in which the pin configuration is the opposite of what you want: the DAC’s input pins move from bit 7 to bit 0 going downward, whereas the MCU’s output pins move from bit 7 to bit 0 going upward. I couldn’t remedy this by re-assigning the microcontroller pins because I wanted the data bits to correspond to the actual bits of the Port 2 register (so that I could write a full byte to the DAC without moving bits around). So I ended up with some awkward routing, but nothing terrible.
By Dorian Yannic. Electrical Wiring. Published at Wednesday, December 27th 2017, 23:07:44 PM. SMT fixtures are rigid PCB carriers that allow manufacturers to load single or multiple irregular boards, and then take them through the standard processing machines. This makes it possible to carry out tasks such as automatic mounting of electronic components, infra-red reflow soldering, wave soldering, automatic testing, etc.
By Fleurette Nina. Motor Wiring. Published at Monday, December 04th 2017, 21:51:01 PM. RC servos are used to provide actuation for various mechanical systems such as the steering of a car, the control surfaces on a plane, or the rudder of a boat. Due to their affordability, reliability, and simplicity of control by microprocessors, they are often used in small-scale robotics applications. A standard RC receiver (or a microcontroller) sends pulse-width modulation (PWM) signals to the servo. The electronics inside the servo translate the width of the pulse into a position. When the servo is commanded to rotate, the motor is powered until the potentiometer reaches the value corresponding to the commanded position.
By France Barbara. Motor Wiring. Published at Saturday, December 02nd 2017, 17:02:52 PM. The circular arrangement of electromagnets is divided into groups, each group called a phase, and there is an equal number of electromagnets per group. The number of groups is chosen by the designer of the stepper motor. The electromagnets of each group are interleaved with the electromagnets of other groups to form a uniform pattern of arrangement. For example, if the stepper motor has two groups identified as A or B, and ten electromagnets in total, then the grouping pattern would be ABABABABAB.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.