By France Barbara. Electrical Wiring. Publised at Sunday, February 11th 2018, 00:47:29 AM. In a demanding application, we may not have the time to continuously check the pointers to see if they have reached the end of the buffer and wrap them back to the beginning of the buffer when necessary. As a result, a DSP processor uses dedicated hardware to provide some fast circular buffers.This hardware implementation automatically checks the status of the pointers and updates them accordingly.
By Olivier Constance. Electrical Wiring. Publised at Monday, February 19th 2018, 05:58:07 AM. I always prefer to maintain a logical flow of signals and functionality in my PCB layouts. I think that this approach results in an easier design process and a better board. The AWG layout progresses from left to right: from power input and communication input/output, to the power supply circuitry, to the processor, to the DAC (which is controlled by the processor and constitutes the board’s transition from digital to analog), to the analog signal-conditioning circuitry, and finally to the output connector. Parts that don’t have a specific position in the functional flow—such as the oscillator (U4), the DAC’s passives (C16, R5, etc.), and the voltage reference (U3)—are arranged near the components that they support.
By Dorian Yannic. Electrical Wiring. Publised at Wednesday, November 22nd 2017, 13:04:57 PM. The datasheet states (see image below) that this IC—specifically the CMOSens® technology that it uses—is "designed for mass production." Umm, should not this go without saying? I have seen datasheets state "not recommended for new designs," but I do not ever recall seeing one that specifies that the IC, or its underlying technology, is designed for mass production. This benefit makes me question if Sensirion has other ICs that are in fact not designed for mass production. It is all a bit puzzling. Have you seen other IC datasheets call this out? If so, please let us know.
By France Barbara. Electrical Wiring. Published at Sunday, December 31st 2017, 21:11:16 PM. The datasheet goes on to say that "the nRESET pin is internally connected to VDD with a pull up resistor of 50 kΩ." So... why are there two options for how to configure the nReset pin when it is not being used? Why not just recommend that it should be left floating (since it is already pulled high internally)? And, if there are indeed technical reasons for when the pin should be externally pulled up to VDD (for better noise immunity, as an example) then let us know what those technical reasons are.
By Fleurette Nina. Electrical Wiring. Published at Sunday, December 31st 2017, 17:25:19 PM. PCBs with SMT on both sides and those with mixed TH and SMTs may start to flex and bow when in the reflow oven or selective soldering machine. For this reason, the maximum size for this type of board is usually smaller than the single-sided. Breaking out the boards manually can stress the board and components near the edges, the solder joints, or leave out rough stubs on the edges
By France Barbara. Motor Wiring. Published at Sunday, December 31st 2017, 11:07:30 AM. A common type of servo provides position control. Commonly, servos are electrical, hydraulic or pneumatic. They operate on the principle of negative feedback, where the control input is compared to the actual position of the mechanical system as measured by some sort of transducer at the output. Any difference between the actual and wanted values (an "error signal") is amplified (and converted) and used to drive the system in the direction necessary to reduce or eliminate the error. This procedure is one widely used application of control theory. Typical servos can give a rotary (angular) or linear output.
By Gaspard Magalie. Motor Wiring. Published at Sunday, December 31st 2017, 07:42:08 AM. The two wires of the brushed dc motor can be thought of as forward and reverse. The three wires of brushless can be thought of as 1, 2 and 3. Going forward would be this sequence 1-2, 2-3, 3-1, 1-2, etc. Going backwards would be 1-3, 3-2, 2-1, 1-3, etc. What this means is that one third of the motor is helping maintain momentum while another third is pulling the motor in a new direction.
By Mailys Laurent. Motor Wiring. Published at Sunday, December 31st 2017, 05:19:37 AM. A micro controller or stepper motor controller can be used to activate the drive transistors in the right order, and this ease of operation makes unipolar motors popular with hobbyists; they are probably the cheapest way to get precise angular movements. For the experimenter, the windings can be identified by touching the terminal wires together in PM motors. If the terminals of a coil are connected, the shaft becomes harder to turn.
By Dorian Yannic. Motor Wiring. Published at Sunday, December 31st 2017, 04:44:25 AM. After the retaining ring is removed, the entire assembly that spins can be removed. There may be some resistance that feels like removing magnets from each other. Underneath the cup of all outrunner brushless motors is a series of coils. On some motors, between the coils, are hall effect probes. Hall effect probes detect the spinning magnetic field and provide a pulse out of the brushless motors to the electronics. From this pulse the electronics can precisely control the speed of the motor
By Fleurette Nina. Electrical Wiring. Published at Sunday, December 31st 2017, 02:18:44 AM. Processing irregular and fragile PCBs in standard assembly machines is often a challenge. Due to their non-standard dimensions, the oddly shaped, thin, or fragile boards do not fit properly in the reflow, component placement, or other standard processing machines. Lack of adequate support and alignment may strain, bend or damage the fragile boards as they go through the processing system. In addition, this may impact the accuracy of the process.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.