By Olivier Constance. Car Wiring. Publised at Monday, January 01st 2018, 11:51:08 AM. To fit a spade terminal, slip the insulating cover over the wire and push it up the wire, out of the way. Use a wire stripper to remove about 1/8in. (3 mm) of insulation from the end of the wire. Lay the bare strands in the inner section of the connector. Use crimping pliers to tighten the two small tongues firmly around the insulated part of the wire. On the other side of the connector, push the wire strands back and down flat. Hold the connector blade upwards to avoid solder running into the spade part.
By Cyrille Lothaire. Car Wiring. Published at Saturday, December 30th 2017, 02:17:52 AM. If possible, use an insulated in-line crimp connector. Test each mended wire with a circuit tester and battery, connected to the nearest connectors either side of the mend. Re-wrap the exposed section of the loom with self-adhesive or "clingfilm" PVC insulating tape. Put some layers between the exposed section and adjoining wires - not merely a cover over the top - then fit the loom back into the car. Reconnect all terminals and clips, then test all the electrical components involved.
By Gaspard Magalie. Electrical Wiring. Published at Friday, December 29th 2017, 23:04:12 PM. Fixtures are more suited for the flexible circuit boards as well as the fragile and thin PCBs. However, each new board design requires its custom fixture which can take between three and four days for a manufacturer to produce and deliver. As such, using fixtures can add up the costs and time to produce the PCBs.
By Claudine Nicolette. Electrical Wiring. Published at Friday, December 29th 2017, 20:19:29 PM. Processing irregular and fragile PCBs in standard assembly machines is often a challenge. Due to their non-standard dimensions, the oddly shaped, thin, or fragile boards do not fit properly in the reflow, component placement, or other standard processing machines. Lack of adequate support and alignment may strain, bend or damage the fragile boards as they go through the processing system. In addition, this may impact the accuracy of the process.
By Adrienne Emmanuel. Electrical Wiring. Published at Friday, December 29th 2017, 20:12:23 PM. The fixtures are usually available in a variety of designs, materials, sizes, and thicknesses. Some can carry more than one board hence allowing the processing of multiple PCBs simultaneously. Other designs have adjustments to support both the primary and secondary side processes.
By Dorian Yannic. Electrical Wiring. Published at Friday, December 29th 2017, 15:30:43 PM. Although this device uses an I2C interface with communication speeds up to 1 MHz, two of the eight pins are dedicated to Alert (pin3) and nReset (pin 6). The Alert pin is intended to be connected, if desired, to an interrupt pin on a microcontroller. According to section 3.5 (ALERT Pin) of the datasheet, "The output of the pin depends on the value of the temperature reading relative to programmable limits," and its function is "explained in a separate application note.
By Mailys Laurent. Electrical Wiring. Published at Friday, December 29th 2017, 09:43:55 AM. However, and this is very perplexing, there is no additional information related to the "separate application note." My suspicion is that Sensirion intended to include a link to this app note but then simply forgot to include it; perhaps additional information will be provided in the datasheet next revision.
By Fleurette Nina. Motor Wiring. Published at Friday, December 29th 2017, 08:52:17 AM. A micro controller or stepper motor controller can be used to activate the drive transistors in the right order, and this ease of operation makes unipolar motors popular with hobbyists; they are probably the cheapest way to get precise angular movements. For the experimenter, the windings can be identified by touching the terminal wires together in PM motors. If the terminals of a coil are connected, the shaft becomes harder to turn.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.